[2026] Valid NACE-CIP2-001 test answers & NACE NACE-CIP2-001 exam pdf
Verified NACE-CIP2-001 dumps Q&As - Pass Guarantee or Full Refund
NACE-CIP2-001 exam consists of two parts: a written exam and a practical exam. The written exam consists of 120 multiple-choice questions and covers topics such as surface preparation, coating application, coating inspection, and equipment. The practical exam tests the candidate’s ability to apply their knowledge in a real-world scenario by conducting coating inspections and reporting their findings.
NACE-CIP2-001 certification exam covers a wide range of topics related to coatings, including surface preparation, coating application, inspection methods, and quality control. It also includes questions on safety, environmental regulations, and industry standards. Candidates must demonstrate a thorough understanding of these topics in order to pass the exam and earn their certification.
NEW QUESTION # 19
Application of Thermal Spray Coatings requires:
- A. Specialized skills supported by training and experience
- B. The same skills as welding
- C. The same skills as liquid coatings
- D. No particular skills
Answer: A
NEW QUESTION # 20
Steel shot grit contaminated with oil or grease used in a cetrifugal blast cleaning should be
- A. washed with clean potable water prior to Use.
- B. run through the air wash separator.
- C. disposed of properly.
- D. mixed with uncontaminated abrasive
Answer: C
NEW QUESTION # 21
When using a destructive Paint Inspection Gauge the NACE inspector must:
- A. Determine the Dry Film Thickness of the coating prior to use
- B. Ensure the glue on the dolly is properly applied prior to use
- C. Select the appropriate hand wheel based on the measured Dry Film Thickness prior to us
- D. Consult SSPC Guide 1 prior to use
Answer: A
NEW QUESTION # 22
When conducting inspections the Inspector should follow which standards:
- A. Australian standards in Australia
- B. ISO standards in Europe and Asia
- C. NACE and SSPC standards in North America
- D. The specified standards
Answer: D
NEW QUESTION # 23
A failure caused by applying a coating too thinly is known as
- A. failure to cure.
- B. cracking.
- C. pinholes.
- D. chalking.
Answer: C
NEW QUESTION # 24
When measuring the Dry Film Thickness Of liquid coatings applied to galvanized ferrous substrates the most commonly used instrument is the:
- A. Eddy Current Gauge
- B. Ultra Sonic DFT Gauge
- C. Magnetic Gauge
- D. Tooke Gauge
Answer: D
NEW QUESTION # 25
When observing fabrication defects the NACE Inspector should:
- A. Require they be corrected prior to coating
- B. Consult the specification to determine how they should be treated
- C. Write an NCR and call the fabricator
- D. Stop the job immediately
Answer: B
NEW QUESTION # 26
You are a NACE Level 2 Coating Inspector who has just arrived on a job in progress where there is no Inspection and Test Plan (ITP). The first morning you arrive the job is behind schedule and you are asked to take DIY Film Thickness readings.
Your FIRST preferred course of action is to:
- A. Use a generally accepted industry standard and to take readings
- B. Develop your own methodology and proceed take the readings
- C. Refuse to take readings until an is in place
- D. Call your supervisor
Answer: A
NEW QUESTION # 27
A single component water borne acrylic coating cures by:
- A. Co-Reaction
- B. Oxidation
- C. Coalescence
- D. Solvent Evaporation
Answer: C
NEW QUESTION # 28
In the event of a conflict between the Product Data Sheet and the Specification:
- A. The Specification prevails
- B. It is up to the Inspector to decide which one to follow
- C. The Product Data Sheet prevails
- D. It is up to the Applicator to decide which one to follow
Answer: A
NEW QUESTION # 29
Which product, is used in conjunction with other coatings such as FBE when the lines run through wetlands or a body of water?
- A. 3-Layet Polyethylene (PE)
- B. Coal Tar Enamel
- C. Concrete
- D. 2-Layet Polyethylene (PE)
Answer: C
NEW QUESTION # 30
NACE International Standards are developed by:
- A. Regional mandates
- B. International mandates
- C. Government mandates
- D. Standard committees
Answer: D
NEW QUESTION # 31
You are the NACE Level 2 Coating Inspector where SSPC PA 2 has been specified with an additional requirement that no individual gauge reading shall be below a certain value.
As this is not part of the standard you should:
- A. Enforce the additional requirement
- B. Call your supervisor
- C. Ignore the additional requirement
- D. Request clarification from the specifier
Answer: A
NEW QUESTION # 32
Which type of pipelines collect the gas from the transmission system so utility companies can distribute the gas to end users?
- A. Gathering
- B. Transmission
- C. Distribution
- D. Midstream
Answer: C
NEW QUESTION # 33
As a NACE Level 2 Inspector on a field job; prior to submission your documentation should always reviewed and approved by:
- A. A NACE Level 1 Inspector
- B. A NACE Level 3 Inspector
- C. A NACE Protective Coating Specialist
- D. Another NACE Level 2 Inspector
Answer: B
NEW QUESTION # 34
Surface preparation of concrete is performed using:
- A. Methods that are the same as wood
- B. Methods that are completely different to steel
- C. Methods that have been modified for concrete
- D. Methods that are exactly the same as steel
Answer: C
NEW QUESTION # 35
When NACE/SSPC WJ 1 is referenced; what type of equipment would the Inspector expect to see on the job:
- A. Abrasive Blasting Equipment
- B. Power Tools
- C. Scarifiers
- D. Water Jetting Equipment
Answer: D
NEW QUESTION # 36
The solvent sensitivity/solvent wipe test (ASTM D4752) is used to determine the cure of
- A. epoxies.
- B. powder coatings.
- C. inorganic zincs.
- D. urethanes.
Answer: C
NEW QUESTION # 37
......
NACE-CIP2-001 Exam Questions – Valid NACE-CIP2-001 Dumps Pdf: https://www.freepdfdump.top/NACE-CIP2-001-valid-torrent.html
NACE-CIP2-001 PDF Dumps Recently Updated Questions: https://drive.google.com/open?id=1j5z2h4Cb6st9AFAHzwtsNeSx0kv-Zcmk
