The Best Network Appliance NS0-183 Study Guides and Dumps of 2021
Top Network Appliance NS0-183 Exam Audio Study Guide! Practice Questions Edition
NetApp NS0-183 Exam Topics:
| Section | Objectives |
|---|---|
| ONTAP Networking | - Describe the cluster network, e.g., multi-node, single node clusters - Demonstrate knowledge of the purpose of the management network - Identify the networking components in a cluster environment |
| ONTAP Switches | - Identify the functions of supported switches - Demonstrate knowledge of how to configure/verify configuration requirements |
| Customer Handoff | - Describe how to complete the service report - Demonstrate knowledge of handoff procedures to the customer - Demonstrate knowledge of how to communicate completion and possible problem status - Identify contacts for additional help after handoff |
| Basic Installation Topics and Tools | - Describe installation preparation steps - Describe basic equipment installation steps |
| ONTAP Configuration | - Describe how to use NetApp configurations - Demonstrate knowledge of how a node should be added or replaced |
| ONTAP Concepts | - Identify general cluster terms used during installation - Identify ONTAP licensing for 9.7 |
NEW QUESTION 70
When you install a new ONTAP 9.7 4-node cluster, which network type is required?
- A. cluster interconnect
- B. peering network
- C. data network
- D. intercluster network
Answer: A
NEW QUESTION 71
Click the Exhibit button.
You plan to install a new ONTAP cluster at a customer site by using the new ONTAP System Manager 9.7 GUI.
Referring to the exhibit, what must you do before you provision initial storage?
- A. Configure protocols.
- B. Configure cluster LIFs.
- C. Configure aggregates.
- D. Configure a remote tier.
Answer: C
NEW QUESTION 72
You want to create a new intercluster LIF for cross-cluster replication and use the CLI. After you create the nac101_intercluster_lif_icl LIF, you are not able to see the LIF in the list of local intercluster LIFs.
Referring to the exhibit, what is the problem?
- A. The LIF that was created has the wrong role type.
- B. The home node of the new intercluster LIF has reached the maximum of four intercluster LIFs.
- C. The intercluster LIF has assigned an IP address that is not in the intercluster VLAN.
- D. The assigned port for the intercluster e1c LIF is in the down admin state.
Answer: A
NEW QUESTION 73
Click the Exhibit button.
Referring to the exhibit, what information is forwarded to syslog after you enter the scripted install commands? (Choose two.)
- A. AutoSupport messages
- B. command history
- C. SNMP traps
- D. EMS messages
Answer: A,B
NEW QUESTION 74
Node 3 has taken over Node 4. You are attempting to access Node 4 on its management interface but cannot do it. In this scenario, how would you access Node 4's management interface?
- A. Connect to the node management on Node 3 and then use the HA interconnect to access node 4.
- B. You should use SSH directly to one of the cluster interconnect switches; from there, you can use SSH to the node management on node 4.
- C. You have not waited long enough for the failover timeout for a node management LIF; there is a broadcast domain configured for this situation.
- D. You must use the Service Processor; node management LIFS do not fall over between nodes.
Answer: D
NEW QUESTION 75
Which statement about LIFs is true?
- A. One port can host multiple data LIFs.
- B. A data LIF can be associated with multiple SVMs.
- C. One cluster-management LIF exists per node.
- D. Cluster LIFs and data LIFs can share a port.
Answer: A
NEW QUESTION 76
You are installing a new AFF A400 cluster for a customer. The customer indicates that they want to take advantage of AutoSupport On Demand.
In this scenario, which AutoSupport transport protocol must you use?
- A. HTTPS
- B. HTTP
- C. SMTP
- D. FTP
Answer: A
NEW QUESTION 77
Click the Exhibit button.
Your ONTAP cluster shows the cluster network errors that are shown in the event log.
What is used by ONTAP software to log the errors that are shown in the exhibit?
- A. EMS
- B. SNMP
- C. BGP
- D. AutoSupport
Answer: A
NEW QUESTION 78
In a 4-node cluster, what are two functions of the HA interconnect? (Choose two.)
- A. It provides the ability to synchronize the cluster configuration.
- B. It provides nondisruptive operations and fault tolerance.
- C. It provides the ability to relocate the aggregate ownership.
- D. It provides the ability to migrate a data aggregate to any node in the cluster.
Answer: B,C
NEW QUESTION 79
You have just racked a new 6-node switched cluster with ONTAP 9.7. You need to configure the cluster switches.
In this scenario, which two elements would be used to complete the configuration? (Choose two.)
- A. SSH
- B. serial port
- C. SFP+ port
- D. rlogin
Answer: A,B
NEW QUESTION 80
You have just completed the installation of a FAS9000 HA pair with ONTAP 9.5.
In this scenario, according to NetApp best practices, which two tests verify the HA failover functionality? (Choose two.)
- A. Pull the motherboard out of the slot.
- B. Power cycle the node.
- C. Disconnect the HA interconnect cabling.
- D. Invoke a system core.
Answer: B,D
NEW QUESTION 81
In ONTAP 9.7 software, how many different replicated databases (RDBs) exist per node?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
NEW QUESTION 82
In ONTAP 9.7 software, how many different replicated databases (RDBs) exist per node?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
Explanation:
Explanation/Reference: https://www.storagefreak.net/2017/08/netapp-cdot-ontap-9-rdb-and-cluster-replication-ring
NEW QUESTION 83
You are planning to update your running switch environment. You must know that certain conditions exist before the FASTPATH software and the RCF on a NetApp CN1610 cluster switch can be installed.
Which condition must exist in this scenario?
- A. You can only update your switch environment within offline windows.
- B. You must set the port configuration to default for all ports before running the portcfgdefaultport-numbercommand.
- C. All ISL ports must be moved to a different switch.
- D. All cluster logical interfaces (LIFs) must be up and must not have been migrated.
Answer: D
NEW QUESTION 84
Which statement is true about cluster interconnect?
- A. It provides the core data network communication.
- B. It is needed for the replication network between clusters.
- C. It transports the data between nodes if a Data LIF has a non-optimized path.
- D. It is a management network for cluster administration and can be used for interconnect LIFs.
Answer: C
NEW QUESTION 85
What are two reason why automatic giveback fails? (Choose two.)
- A. NFS sessions are established.
- B. SAN sessions are established.
- C. The disk shelf is too hot.
- D. Storage failover is disabled.
Answer: C,D
NEW QUESTION 86
You are adding new controllers to an existing cluster. As part of the upgrade process, you have updated the BES-53248 cluster switches.
In this scenario. Which two commands would you use to verify a healthy cluster after the upgrade? (Choose two.)
- A. network port show -ipspace Cluster
- B. network device-discovery show -protocol cdp
- C. network interface show -vserver Cluster
- D. network interface show -vserver Cluster -fields auto-revert
Answer: A,C
NEW QUESTION 87
You are completing an ONTAP base installation, and your customer is asking you to create two SVMs, one for NFS and one for SMB.
Which type of SVM needs to be created to complete the installation?
- A. system SVM
- B. data SVM
- C. multitenancy node SVM
- D. admin SVM
Answer: B
NEW QUESTION 88
You want to verify that connections are cables correctly and that shelf IDs are unique within an HA pair.
Which tool would be used to accomplish these tasks?
- A. Active IQ Config Advisor
- B. Active IQ Unified Manager
- C. System Diagnostics
- D. Cloud Insights
Answer: C
NEW QUESTION 89
......
Valid NS0-183 Exam Updates - 2021 Study Guide: https://www.freepdfdump.top/NS0-183-valid-torrent.html
